環氧接地銅箔網絡概述：

環氧自流平防靜電地面的施工內容中，包含有銅箔構成的網絡，這些金屬網絡彼此形成電氣通路，用于防靜電地面的靜電傳導。作為電氣設計配合，應該將防靜電地面所在的建筑柱上，適當預留接地端子盒。在地面施工完畢后，將防靜電地面內的金屬線與該接地端子盒相連。另外，該接地端子在土建施工過程中須通過柱內主筋與接地極焊接連通，以使靜電通過接地端子沿柱內主筋流向地極。防靜電接地電阻一般要求不大于10歐姆。

1、工藝流程

2、施工方法

清理地面，尋找中心線。首先將地面浮灰清除干凈，然后用量具找出房間的中心位置，畫出中心十字線，要求十字線垂直等分。

在地面底涂施工完成涂料充分干透后，進行二次打磨處理并進行地面的清潔維護，施工區域用警示帶等標示性的材料進行隔離，以防止人員誤闖入施工區域。做好上述準備后就可以進行導電膠層的施工，導電層施工利用刮板進行涂裝作業，要求導電層涂料厚度均勻。

鋪設銅箔網絡：在銅箔涂上少許導電膠，從中心位置開始相鄰鋪于地面，縱向2.4米到3.6米鋪設--根銅箔。銅箔必須有兩處以上沿墻壁用6平方的軟編織帶引出約700mm，引出的編織帶與等電位端子箱相連，并選用PVC 線槽進行保護，等電位端子箱內裝40*4的銅排，預留10個M8螺栓。

銅箔敷設完成后，進行中涂的施工，然后是面層，整個過程按序進行。